DANFOSS FC-304 VFD DRIVE PARAMETER SETTINGS

DANFOSS FC-304 VFD DRIVE PARAMETER SETTINGS

DANFOSS FC-304


DANFOSS FC-304 VFD DRIVE PARAMETER LIST 

Parameter

Setting

Description

1-20

22 kw

Motor Kilowatt

1-21

18 HP

Motor HP

1-22

415 Volt

Motor Voltage

1-23

50 Hz

Motor Frequency

1-24

23 Amps

Motor Current

1-25

1450 Rpm

Motor Speed

3-00

0

Min - Max

3-01

3

HZ

3-02

0 Hz

Min Reference

3-03

50 Hz

Max Reference

3-04

Reference Function

 

3-12

No Operation

 

3-13

0

Linked to Hand / Auto

3-14

50 Hz

 

3-15

1

Reference Resource (Analog Input 53)

3-41

30 s

Ramp Up

3-42

30 s

Ramp Down

4-12

0.0 Hz

Motor speed limit low

4-14

50 Hz

Motor speed limit High

5-40

5

Function Relay (Drive Running)

6-10

0.0 v

53 Low Voltage

6-11

10.0 v

53 High Voltage

6-14

30 Hz

Terminal 53 low ref / feed back

6-15

40 Hz

Terminal 53 High ref / feed back

8-50

2 (logic AND)

Costing

8-51

3 (Logic OR)

Quick stop

8-52

3 (Logic OR)

DC Brake

8-53

3 (Logic OR)

Start

8-54

3 (Logic OR)

Reversing

8-55

3 (Logic OR)

Set up select

8-56

3 (Logic OR)

Presence Ref Select

 

 

 

 

 

 

 

 

 

This Parameter Setting is Suitable for Manual ON/OFF Mode , Auto Frequency Mode , its Deepened on (0-10)v Dc signal.

 

DANFOSS 301 , 304 TERMINAL CONNECTION

 




To Reset the Danfoss Vfd Drive First ‘SWITCH OFF’ the Drive Main Power Supply. Then After ‘SWITCH ON ‘ the Drive Main Power Supply
Before Press ( Status + Menu + OK ) Button simultaneity after the Drive will Completely in Factory Reset Condition.



VIDEO LINK

DANFOSS INVERTER FC-301 / 302 Setting Parameters (Part-3)
https://www.youtube.com/watch?v=2X_b0k9QKGI

DANFOSS INVERTER FC-301 / 302 Setting Parameters (Part-2)
 https://www.youtube.com/watch?v=2KQfHeHm-Ag

DANFOSS INVERTER FC-301 / 302 Setting Parameters (Part-1)
https://www.youtube.com/watch?v=dYbZ6CYAtwk






Comments

Post a Comment

Popular posts from this blog

QElectro Tech Software Overview

Image
  In This Article we are going to see QElectro Tech Software Overview... QElectro Tech QElectroTech QElectroTech is a free software to create electric diagrams. QElectroTech or QET in short is currently available in version 0.80. This Software is Very Effective and Very Useful for Electronic, Electrical, and Instrumentation Department Engineers. Compare to other Diagram Software’s ‘exe’ Setup file of QElectro Tech Software Size is Too Low. There are Lot of Electrical, Electronic and Instrumentation Symbols and elements are in this QElectro Tech software. The Software of Table of Contents is following of ( Basics , Interface , Preferences , Project , Folio , Element , Conductor , Schema , Drawing , Reports , Export and print , Annex etc..) QElectro Tech Documentation 1 QElectro Tech Documentation 2 The QElectro Tech Software contains many collections (Electrical , Logic , Hydraulic , Pneumatic and Energy symbols and Elements) also user can create they own symbols. Anyone can Access
Read More »

Danfoss VLT micro drive FC 51 Name Plate

Image
In this Article, we are going to discuss about what specifications are mentioned on the Danfoss VLT micro drive FC 51 name plate sticker. Welcome to controls and systems blog page, The nameplate sticker is located on the top of each VFD drives and shows the ratings, serial number, warnings catalog number, and other relevant data for each unit. This nameplate sticker is mostly the same in the VLT model VFD drives, with only a few changes in the some VLT model VFD drives. 1 st ROW: ( TYPE CODE ) Position 1 - 3 [FC]-  is Product group, Possible choice is: Frequency converters, Position 4 - 6 [051]  is Series and product type, Possible choice is: Micro Drive, Position 7 - 10  [P]  is Power size, Possible choice is: 0.18 to 22 kilo watt. Position 11 - 12  [S2]  is Mains voltage, Possible choice is: S2 that means Single phase 200 to 240 Volt AC, T2 that means 3-phase, 200 to 240 Volt AC, T4 that means 3-phase, 380 to 480 Volt AC, Position 13 - 15  [E20]  i
Read More »

SIEMENS V20 VFD DRIVE FAULTS CODE LIST PART-1

Image
In this article  we are going to discuss about siemens v20 vfd drive fault Cause and Remedy for this  fault codes ( F1, F2 , F3 , F4 , F5 , F6 , F11 , F12 , F20 , F35 )   SIEMENS V20 DRIVE F1  -  FAULT:    Overcurrent CAUSE : Motor power (P0307) does not correspond to the inverter power (r0206). Motor lead short circuit Earth faults r0949 = 0: Hardware reported r0949 = 1: Software reported r0949 = 22: Hardware reported REMEDY : Check the following: Motor power (P0307) must correspond to inverter power (r0206). Cable length limits must not be exceeded. Motor cable and motor must have no short-circuits or earth faults. Motor parameters must match the motor in use. Value of stator resistance (P0350) must be  correct. Motor must not be obstructed or overloaded. Increase ramp-up time (P1120) Reduce starting boost level (P1312) F2  -  FAULT:  Overvoltage CAUSE : Main supply voltage too high Motor is in regenerative mode r0949 = 0: Hardware reported r0949 = 1 or 2: Software reported REMEDY
Read More »

SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST

Image
   SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST This Parameter Setting is Suitable for (  Manual ON/OFF Mode , Auto Frequency Mode , Pot meter Varying Mode ) its Deepened on (0-10)v Dc signal. SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST   Parameter Setting Description P0003 1 Standard: Allows access into most frequently used parameters P0010 30 Factory setting P0970 1 Resets all parameters P0010 1 Quick commissioning P0100 0 Europe [kW], motor base frequency is 50 Hz P0301 22 Rated motor KW [KW] P0304 415 Rated motor voltage [V] P0305 35 Rated motor current [A] P0307 22 Rated motor power P0308 0.82 Rated motor cosĪ† P0310
Read More »

Siemens RDG400KN Thermostat Parameter List

Image
In This Article we are going to see Siemens RDG400KN Room Thermostat Parameter List. RDG400KN Thermostat Control Parameter Heating only If you wish to change control parameters, proceed as follows: Press Left and Right button simultaneously for at least 3 seconds. Release them and within 2 seconds, press the Right button again for 3 seconds (The display will show P01). Select the required parameter by turning the rotary knob. Press button (OK). The current value of the selected parameter starts blinking and can be changed by turning the rotary knob. Press button (OK) to confirm the adjusted value, or (Esc) to cancel the change. If you wish to adjust additional parameters, repeat step 3 through 5, or press (Esc) to leave the parameter setting mode.
Read More »