DANFOSS VLT 6000 VFD DRIVE PARAMETER LIST

 

 DANFOSS VLT 6000 VFD DRIVE PARAMETER LIST 

VLT 6000


DANFOSS VLT 6000 VFD DRIVE PARAMETER LIST 

Parameter

Setting

Description

012

Disable

Hand Start Button

013

Enable

Auto Start Button

102

15 KW

Motor Power

103

415 V

Motor Voltage

104

50 Hz

Motor Frequency

105

28 A

Motor Current

106

1450 Rpm

Motor Speed

118

0.75

Motor Power Factor

200

0-120 Hz

Frequency Range

201

0.0 Hz

Min Frequency

202

50 Hz

Max Frequency

203

Linked to Hand / Auto

Reference site

204

0 Hz

Min Reference

205

50 Hz

Max Reference

206

30 s

Ramp up Time

207

30 s

Ramp Down Time

210

SUM

Ref. function

300

Reset

Digital Input 16

301

Freeze Reference

Digital Input 17

302

Start

Digital Input 18

303

Reversing

Digital Input 19

304

Coast Inverse

Digital Input 27

305

Jog

Digital Input 29

306

No Operation

Digital Input 32

307

No Operation

Digital Input 33

308

Reference

AI [V] Function

309

0 v

AI 53 Scale Low

310

10 v

AI 53 Scale High

413

0 %

Min . Feedback

414

100 %

Max . Feedback

415

%

Ref / Feedback unit

416

Liner

Feed back Con

503

Logic OR

Coasting

504

Logic OR

Dc Brake

505

Logic OR

Start

506

Digital Input

Reversing

507

Logic OR

Select. setup

508

Logic OR

Select Speed

 

 

 

This Parameter Setting is Suitable for Manual ON/OFF , Mode , Auto Frequency Mode , its Deepened on (0-10)v Dc signal.

  •  This Parameter Setting is Suitable for Manual ON/OFF Mode , Auto Frequency Mode , its Deepened on (0-10)v Dc signal

DANFOSS VLT 6000 TERMINAL CONNECTION




Comments

Post a Comment

Popular posts from this blog

QElectro Tech Software Overview

Image
  In This Article we are going to see QElectro Tech Software Overview... QElectro Tech QElectroTech QElectroTech is a free software to create electric diagrams. QElectroTech or QET in short is currently available in version 0.80. This Software is Very Effective and Very Useful for Electronic, Electrical, and Instrumentation Department Engineers. Compare to other Diagram Software’s ‘exe’ Setup file of QElectro Tech Software Size is Too Low. There are Lot of Electrical, Electronic and Instrumentation Symbols and elements are in this QElectro Tech software. The Software of Table of Contents is following of ( Basics , Interface , Preferences , Project , Folio , Element , Conductor , Schema , Drawing , Reports , Export and print , Annex etc..) QElectro Tech Documentation 1 QElectro Tech Documentation 2 The QElectro Tech Software contains many collections (Electrical , Logic , Hydraulic , Pneumatic and Energy symbols and Elements) also user can create they own symbols. Anyone can Access
Read More »

Danfoss VLT micro drive FC 51 Name Plate

Image
In this Article, we are going to discuss about what specifications are mentioned on the Danfoss VLT micro drive FC 51 name plate sticker. Welcome to controls and systems blog page, The nameplate sticker is located on the top of each VFD drives and shows the ratings, serial number, warnings catalog number, and other relevant data for each unit. This nameplate sticker is mostly the same in the VLT model VFD drives, with only a few changes in the some VLT model VFD drives. 1 st ROW: ( TYPE CODE ) Position 1 - 3 [FC]-  is Product group, Possible choice is: Frequency converters, Position 4 - 6 [051]  is Series and product type, Possible choice is: Micro Drive, Position 7 - 10  [P]  is Power size, Possible choice is: 0.18 to 22 kilo watt. Position 11 - 12  [S2]  is Mains voltage, Possible choice is: S2 that means Single phase 200 to 240 Volt AC, T2 that means 3-phase, 200 to 240 Volt AC, T4 that means 3-phase, 380 to 480 Volt AC, Position 13 - 15  [E20]  i
Read More »

SIEMENS V20 VFD DRIVE FAULTS CODE LIST PART-1

Image
In this article  we are going to discuss about siemens v20 vfd drive fault Cause and Remedy for this  fault codes ( F1, F2 , F3 , F4 , F5 , F6 , F11 , F12 , F20 , F35 )   SIEMENS V20 DRIVE F1  -  FAULT:    Overcurrent CAUSE : Motor power (P0307) does not correspond to the inverter power (r0206). Motor lead short circuit Earth faults r0949 = 0: Hardware reported r0949 = 1: Software reported r0949 = 22: Hardware reported REMEDY : Check the following: Motor power (P0307) must correspond to inverter power (r0206). Cable length limits must not be exceeded. Motor cable and motor must have no short-circuits or earth faults. Motor parameters must match the motor in use. Value of stator resistance (P0350) must be  correct. Motor must not be obstructed or overloaded. Increase ramp-up time (P1120) Reduce starting boost level (P1312) F2  -  FAULT:  Overvoltage CAUSE : Main supply voltage too high Motor is in regenerative mode r0949 = 0: Hardware reported r0949 = 1 or 2: Software reported REMEDY
Read More »

SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST

Image
   SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST This Parameter Setting is Suitable for (  Manual ON/OFF Mode , Auto Frequency Mode , Pot meter Varying Mode ) its Deepened on (0-10)v Dc signal. SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST   Parameter Setting Description P0003 1 Standard: Allows access into most frequently used parameters P0010 30 Factory setting P0970 1 Resets all parameters P0010 1 Quick commissioning P0100 0 Europe [kW], motor base frequency is 50 Hz P0301 22 Rated motor KW [KW] P0304 415 Rated motor voltage [V] P0305 35 Rated motor current [A] P0307 22 Rated motor power P0308 0.82 Rated motor cosĪ† P0310
Read More »

Siemens RDG400KN Thermostat Parameter List

Image
In This Article we are going to see Siemens RDG400KN Room Thermostat Parameter List. RDG400KN Thermostat Control Parameter Heating only If you wish to change control parameters, proceed as follows: Press Left and Right button simultaneously for at least 3 seconds. Release them and within 2 seconds, press the Right button again for 3 seconds (The display will show P01). Select the required parameter by turning the rotary knob. Press button (OK). The current value of the selected parameter starts blinking and can be changed by turning the rotary knob. Press button (OK) to confirm the adjusted value, or (Esc) to cancel the change. If you wish to adjust additional parameters, repeat step 3 through 5, or press (Esc) to leave the parameter setting mode.
Read More »