SIEMENS BACnet Commercial Thermostat RDY2000BN Parameter List

In This Article we are going to see SIEMENS BACnet Commercial Thermostat RDY2000BN Model Parameter List 101 to 911.

thermostat
RDY2000BN Thermostat


Sequence of Operation

( Control Temperature Setpoints , Effective Room Temperature , 

Heating/Cooling Switchover , Staging Control , Compressor Operation , 

Electric Heat (Optional) , Gas Furnace (Optional) , Fan Operation ,
 
Humidification , Dehumidification , Occupancy Notification , Economizer Enable , 

Pre-Purge , Semi-Continuous Fan , Air Quality Management , 

Service and Fault Messages , Sensor Failure Handling , I/O Test Mode , 

Overcurrent Protection , BACnet Scheduler ).


Siemens Thermostat



Parameter 101 to 113


Parameter

Definition

Default

 

P101

System Type

CO

P102

Cooling Stages

2

P103

Heating Stages

2

P104

Aux Heating Stages

0

P105

Fan Operation

ELE

P106

Reversing Value

0

P107

Scheduler Days

2

P109

Units

F

P110

Changeover

YES

P111

Changeover Deadband

5°F (2.5 °C)

P112

Daylight Savings

NO

P113

Display Temp Setpoint

0 = Absolute













Parameter 201 to 225


Parameter

Definition

Default

 

P201

Heat Temp Limit

95°F (35.0 °C)

P202

Cool Temp Limit

50°F (10.0 °C)

P203

Temperature Display Offset

0°F (0 °C)

P204

Override Time Limit

2

P205

Override Temp Limit

-

P206

Heat Pump Compressor Lock Out

OFF

P207

Heat Pump Auxiliary Heat Lockout

OFF

P208

Service UV Lamp

0

P209

Service Humidifier

0

P210

Service Air Filter

0

P211

Keypad Lockout

OFF

P212

Clock Format

12

P213

Backlight

15

P214

Humidity Display Offset

0

P220

Heating Setpoint Comfort

70

P221

Cooling Setpoint Comfort

75

P222

Heating Setpoint Economy

62

P223

Cooling Setpoint Economy

82

P224

Heating Setpoint Protection

40

P225

Cooling Setpoint Protection

104



















Parameter 301 to 320


Parameter

Definition

Default

 

P301

Configurable Input 1 (IN 1)

OFF

P302

Temperature Input 1 Type

1

P303

Temperature Input 1 Low

0°F (-18.0 °C)

P304

Temperature Input 1 High

120°F (50 °C)

P305

Configurable Input 2 (IN 2)

OFF

P306

Temperature Input 2 Type

1

P307

Temperature Input 2 Low

0°F (-18.0 °C)

P308

Temperature Input 2 High

120°F (50 °C)

P309

Configurable Input 3 (IN 3)

OFF

P310

Temperature Input 3 Type

1

P311

Temperature Input 3 Low

0°F (-18.0 °C)

P312

Temperature Input 3 High

120°F (50 °C)

P313

Configurable Input 4 (IN 4)

OFF

P314

Temperature Input 4 Type

1

P315

Temperature Input 4 Low

0°F (-18.0 °C)

P316

Temperature Input 4 High

120°F (50 °C)

P317

Aux Output 1 (OUT 1)

OFF

P318

Aux Output 2 (OUT 2)

OFF

P319

Aux Output 3 (OUT 3 & C3)

OFF

P320

Independent Humidity Control

NO


Parameter 401 to 407


Parameter

Definition

Default

 

P401

Unit Number

-

P402

CO2 Setpoint

1000

P403

Pre-Occupancy Purge

OFF

P404

Occupancy Sensor Min Run Timer

30

P405

Semi-Continuous Fan

ON

P407

Installer Password

Current PW


Parameter 501 to 511


Parameter

Definition

Default

 

P501

Interstage Delay Cooling

5

P502

Interstage Differential Cooling

1°F (0.5 °C)

P503

Cooling Minimum Off Time

5

P504

Cooling Minimum On Time

3

P505

Changeover Delay

10

P506

Cooling Deadband

1°F

P507

Interstage Delay Heating

5

P508

Interstage Differential Heating

Conv = 1°F (0.5°C) HP = 2°F (1°C)

P509

Heating Minimum Off Time

5

P510

Heating Minimum On Time

3 (10 if heat pump)

P511

Heating Deadband

1°F (0.5 °C)


Parameter 601 to 606 & 701,911


Parameter

Definition

Default

 

P601

MS/TP MAC address

255

P602

Baud Rate

A = Auto

P603

Device Instance

4194303

P604

Max Master

127

P605

Serial number

Display only

P606

Max info frames

1

 

P701

Firmware

Display only

 

P911

Expert Password

Current PW














Comments

Post a Comment

Popular posts from this blog

Danfoss VLT micro drive FC 51 Name Plate

Image
In this Article, we are going to discuss about what specifications are mentioned on the Danfoss VLT micro drive FC 51 name plate sticker. Welcome to controls and systems blog page, The nameplate sticker is located on the top of each VFD drives and shows the ratings, serial number, warnings catalog number, and other relevant data for each unit. This nameplate sticker is mostly the same in the VLT model VFD drives, with only a few changes in the some VLT model VFD drives. 1 st ROW: ( TYPE CODE ) Position 1 - 3 [FC]-  is Product group, Possible choice is: Frequency converters, Position 4 - 6 [051]  is Series and product type, Possible choice is: Micro Drive, Position 7 - 10  [P]  is Power size, Possible choice is: 0.18 to 22 kilo watt. Position 11 - 12  [S2]  is Mains voltage, Possible choice is: S2 that means Single phase 200 to 240 Volt AC, T2 that means 3-phase, 200 to 240 Volt AC, T4 that means 3-phase, 380 to 480 Volt AC, ...
Read More »

QElectro Tech Software Overview

Image
  In This Article we are going to see QElectro Tech Software Overview... QElectro Tech QElectroTech QElectroTech is a free software to create electric diagrams. QElectroTech or QET in short is currently available in version 0.80. This Software is Very Effective and Very Useful for Electronic, Electrical, and Instrumentation Department Engineers. Compare to other Diagram Software’s ‘exe’ Setup file of QElectro Tech Software Size is Too Low. There are Lot of Electrical, Electronic and Instrumentation Symbols and elements are in this QElectro Tech software. The Software of Table of Contents is following of ( Basics , Interface , Preferences , Project , Folio , Element , Conductor , Schema , Drawing , Reports , Export and print , Annex etc..) QElectro Tech Documentation 1 QElectro Tech Documentation 2 The QElectro Tech Software contains many collections (Electrical , Logic , Hydraulic , Pneumatic and Energy symbols and Elements) also user can create they own symbols. Anyone can Acc...
Read More »

SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST

Image
   SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST This Parameter Setting is Suitable for (  Manual ON/OFF Mode , Auto Frequency Mode , Pot meter Varying Mode ) its Deepened on (0-10)v Dc signal. SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST   Parameter Setting Description P0003 1 Standard: Allows access into most frequently used parameters P0010 30 Factory setting P0970 1 Resets all parameters P0010 1 Quick commissioning P0100 0 Europe [kW], motor base frequency is 50 Hz P0301 22 Rated motor KW [KW] P0304 415 Rated motor voltage [V] P0305 35 Rated motor current [A] P0307 22 Rated motor power P0308 0.82 Rated motor cosĪ† ...
Read More »

SIEMENS V20 VFD DRIVE FAULTS CODE LIST PART-1

Image
In this article  we are going to discuss about siemens v20 vfd drive fault Cause and Remedy for this  fault codes ( F1, F2 , F3 , F4 , F5 , F6 , F11 , F12 , F20 , F35 )   SIEMENS V20 DRIVE F1  -  FAULT:    Overcurrent CAUSE : Motor power (P0307) does not correspond to the inverter power (r0206). Motor lead short circuit Earth faults r0949 = 0: Hardware reported r0949 = 1: Software reported r0949 = 22: Hardware reported REMEDY : Check the following: Motor power (P0307) must correspond to inverter power (r0206). Cable length limits must not be exceeded. Motor cable and motor must have no short-circuits or earth faults. Motor parameters must match the motor in use. Value of stator resistance (P0350) must be  correct. Motor must not be obstructed or overloaded. Increase ramp-up time (P1120) Reduce starting boost level (P1312) F2  -  FAULT:  Overvoltage CAUSE : Main supply voltage too high Motor is in regenerative mode r0949 = 0: Hardw...
Read More »

SIEMENS VFD FAULTS CODE LIST PART-2

Image
In this article  we are going to discuss about siemens v20 vfd drive fault Cause and Remedy for this fault codes ( F41, F51 , F52 , F60 , F61 , F62 , F63 , F64 , F71 , F72 ) Fault Vfd Drive F41   -  FAULT: Motor data identification  failure Motor CAUSE : Motor data identification failed. r0949 = 0: No load applied r0949 = 1: Current limit level reached during identification. r0949 = 2: Identified stator resistance less than 0.1% or greater than 100%. r0949 = 30: Current controller at voltage limit r0949 = 40: Inconsistency of identified dataset, at least one identification failed Percentage values based on the impedance Zb = Vmot,nom / sqrt(3) /  Imot,nom REMEDY : Check the following: r0949 = 0: is the motor connected to the inverter? r0949 = 1 - 49: are the motor data in P0304 - P0311 correct? Check what type of motor wiring is required (star, delta). F51 -  FAULT:   Parameter EEPROM fault EEPROM CAUSE : Read or write failure while acce...
Read More »