Siemens RDF300, 340,600 Room Thermostat Parameter List Part-1 (Service Level)

In This Article we are going to see Siemens RDF300, RDF340, RDF600 Room Thermostat Parameter List Part-1 Service Level.

Thermostat
SIEMENS RDF300

Control Parameter

Thermostat
Display


1. Operating mode selector / Protection.
2. Change fan operation
3. Adjust setpoint and control parameters


Siemens RDF300
Control Parameter



Parameter List

P01

Description : Control Sequence

Factory Setting : 

2-pipe, single duct [0 to 3] 1 (Cooling only)

4-pipe, [2 to 4] 4 (Heating & Cooling)

Setting Range :

0 = Heating only

1 = Cooling only

2 = Manual H or C

3 = Auto Changeover

4 = Heating & Cooling


P02

Description : Mode selection by user via operating mode button

Factory Setting : 1 (Protection, Comfort)

Setting Range :

1 = Protection, Comfort

2 = Protection, Comfort, Economy


P04

Description : Selection of °C or °F

Factory Setting : °C 

Setting Range : °C or °F


P05

Description : Sensor Calibration

Default Value : 0.0 K

Setting Range : -3 to +3 K


P06

Description : Standard Temperature display 

Default Value : 0 (Room Temp.)

Setting Range : 

0 = Room Temperature

1 = Setpoint


P07

Description : Additional user information 

Default Value : 0 (No Display)

Setting Range : 

0 = No display

1 = Temperature in °C / °F


P08

Description : Comfort basic Setpoint 

Default Value : 21 °C 

Setting Range : 5 to 40 °C 


P09

Description : Minimum Setpoint limitation in comfort  (W-Min comfort) 

Default Value : 5 °C 

Setting Range : 5 to 40 °C


P10

Description : Maximum Setpoint limitation in comfort  (W-Max comfort) 

Default Value : 35 °C 

Setting Range : 5 to 40 °C 


P11

Description : Setpoint of heating in Economy mode (W-heat Eco)

Default Value : 15 °C 

Setting Range : OFF, 5 °C W-cool Eco



P12

Description : Setpoint of cooling in Economy mode (W-cool Eco)

Default Value : 30 °C 

Setting Range : OFF, 40 °C W-heat Eco 


P13

Description : Electric heater in cooling mode 

Default Value : ON 

Setting Range : 

OFF = Disabled

ON = Enable


P14

Description : Button Lock (press operating mode button for 7 seconds to lock or unlock the button) 

Default Value : 0 (Disable)

Setting Range : 

0 = Disabled

1 = Auto Lock

2 = Manual Lock 

Comments

Post a Comment

Popular posts from this blog

Danfoss VLT micro drive FC 51 Name Plate

Image
In this Article, we are going to discuss about what specifications are mentioned on the Danfoss VLT micro drive FC 51 name plate sticker. Welcome to controls and systems blog page, The nameplate sticker is located on the top of each VFD drives and shows the ratings, serial number, warnings catalog number, and other relevant data for each unit. This nameplate sticker is mostly the same in the VLT model VFD drives, with only a few changes in the some VLT model VFD drives. 1 st ROW: ( TYPE CODE ) Position 1 - 3 [FC]-  is Product group, Possible choice is: Frequency converters, Position 4 - 6 [051]  is Series and product type, Possible choice is: Micro Drive, Position 7 - 10  [P]  is Power size, Possible choice is: 0.18 to 22 kilo watt. Position 11 - 12  [S2]  is Mains voltage, Possible choice is: S2 that means Single phase 200 to 240 Volt AC, T2 that means 3-phase, 200 to 240 Volt AC, T4 that means 3-phase, 380 to 480 Volt AC, Position 13 - 15  [E20]  i
Read More »

QElectro Tech Software Overview

Image
  In This Article we are going to see QElectro Tech Software Overview... QElectro Tech QElectroTech QElectroTech is a free software to create electric diagrams. QElectroTech or QET in short is currently available in version 0.80. This Software is Very Effective and Very Useful for Electronic, Electrical, and Instrumentation Department Engineers. Compare to other Diagram Software’s ‘exe’ Setup file of QElectro Tech Software Size is Too Low. There are Lot of Electrical, Electronic and Instrumentation Symbols and elements are in this QElectro Tech software. The Software of Table of Contents is following of ( Basics , Interface , Preferences , Project , Folio , Element , Conductor , Schema , Drawing , Reports , Export and print , Annex etc..) QElectro Tech Documentation 1 QElectro Tech Documentation 2 The QElectro Tech Software contains many collections (Electrical , Logic , Hydraulic , Pneumatic and Energy symbols and Elements) also user can create they own symbols. Anyone can Access
Read More »

SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST

Image
   SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST This Parameter Setting is Suitable for (  Manual ON/OFF Mode , Auto Frequency Mode , Pot meter Varying Mode ) its Deepened on (0-10)v Dc signal. SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST   Parameter Setting Description P0003 1 Standard: Allows access into most frequently used parameters P0010 30 Factory setting P0970 1 Resets all parameters P0010 1 Quick commissioning P0100 0 Europe [kW], motor base frequency is 50 Hz P0301 22 Rated motor KW [KW] P0304 415 Rated motor voltage [V] P0305 35 Rated motor current [A] P0307 22 Rated motor power P0308 0.82 Rated motor cosĪ† P0310
Read More »

SIEMENS V20 VFD DRIVE FAULTS CODE LIST PART-1

Image
In this article  we are going to discuss about siemens v20 vfd drive fault Cause and Remedy for this  fault codes ( F1, F2 , F3 , F4 , F5 , F6 , F11 , F12 , F20 , F35 )   SIEMENS V20 DRIVE F1  -  FAULT:    Overcurrent CAUSE : Motor power (P0307) does not correspond to the inverter power (r0206). Motor lead short circuit Earth faults r0949 = 0: Hardware reported r0949 = 1: Software reported r0949 = 22: Hardware reported REMEDY : Check the following: Motor power (P0307) must correspond to inverter power (r0206). Cable length limits must not be exceeded. Motor cable and motor must have no short-circuits or earth faults. Motor parameters must match the motor in use. Value of stator resistance (P0350) must be  correct. Motor must not be obstructed or overloaded. Increase ramp-up time (P1120) Reduce starting boost level (P1312) F2  -  FAULT:  Overvoltage CAUSE : Main supply voltage too high Motor is in regenerative mode r0949 = 0: Hardware reported r0949 = 1 or 2: Software reported REMEDY
Read More »