Siemens RDE100 Room Thermostat Parameter List

In This Article we are going to see SIEMENS Room Thermostat RDE100 model device Parameter List.


Overview :

SIEMENS RDE100  Thermostat mainly control for Room Temperature Heating Control Systems. its is used to control four (4) modes Comfort, Economy, Auto timer and Protection mode. The Siemens RDE Thermostat is available in two (2) model one is RDE100 Thermostat it is working in Main Power Supply AC 230 voltage and another one is RDE 100.1 Thermostat it is working in Battery Power supply DC 3 volt.


Operation and Settings :

Thermostat
RDE100


  1. Operating mode touch key
  2. Set
  3. OK
  4. Touch key for decreasing a value
  5. Touch key for increasing a value

Display :

Siemens RDE100 Room Thermostat
Display


Parameter List :


Parameter No : P01

Description : Time Format

Setting Range (default) : 

1 = 21:00 hours (default)

2 = 12:00 AM/PM


Parameter No : P02

Description : Selection of °C or °F

Setting Range (default) : 

1 = °C (default)

2 = °F


Parameter No : P03

Description : Standard temperature display

Setting Range (default) : 

1 = Room Temperature (default)

2 = Setpoint


Parameter No : P04

Description : Temperature sensor calibration

Setting Range (default) : -3 to +3 °C Step 0.5 °C (-6 to +6 °F, step 1 °F) Default: 0 °C


Parameter No : P06

Description : Comfort setpoint lock

Setting Range (default) : 

0 = OFF (default)

1 = ON  locked according to setting in permanent temperature setpoint.


Parameter No : P08

Description : Economy setpoint lock

Setting Range (default) : 

0 = OFF (default)

1 = ON  locked according to setting in permanent temperature setpoint.


Parameter No : P09

Description : Buzzer

Setting Range (default) : 

0 = OFF 

1 = ON (default)


Parameter No : P10

Description : Show frost protection icon

Setting Range (default) : 

0 = OFF (default) 

1 = ON


Parameter No : P11

Description : Time Switch type for Auto Timer

Setting Range (default) : 

0 = Individual Days (default)

1 = All 7 days

2 = 5/2 days


Parameter No : P12

Description : Periodic Pump Run

Setting Range (default) : 

0 = OFF (default) 

1 = ON

 

Parameter No : P14

Description : X1 External input (only for RDE100.1)

Setting Range (default) : 

0 = No input

1 = External sensor

2 = Digital Input


Note : 

  • If u Select 1 (External sensor) option means the Next Parameter P15 Setting Range is Automatically Enable the 0 = OFF (default) option.
  • If u Select 2 (Digital Input) option means the P17 parameter will Automatically Enabled.

 


Parameter No : P15

Description : Temperature limitation (only for RDE100.1)

Setting Range (default) : 

0 = OFF (default)

1 = ON


Note : 

  • If u Select 1 (ON) option means the Next Parameter P16 Setting Range is Automatically Enable the (25 to 60 °C, step 1 °C or 77 to 140 °F, step 1 °F ) option.



Parameter No : P16

Description : Maximum limitation temperature for underfloor heating (only for RDE100.1)

Setting Range (default) : 

25 to 60 °C, step 1 °C or

77 to 140 °F, step 1 °F

Default: 30 °C



Parameter No : P17

Description : Window contact features (only for RDE 100.1)

Setting Range (default) : 

0 = Normally Open Contact (default)

1 = Normally Closed Contact


Parameter No : P21

Description : Button scanning rate for the Capacitive buttons (RDE100.1 only)

Note: a shorter scanning rate means shorter battery life.

Setting Range (default) : 

0.2 = 0.25 s

0.5 = 0.5 s

1.0 = 1.0 s (default)

1.5 = 1.5 s


Parameter No : P22

Description : Reload factory settings

Setting Range (default) : 

0 = OFF (default)

1 = reload


Parameter No : P23

Description : Software version information

Setting Range (default) : No adjustment possible.


Parameter No : P78

Description : Control behavior

Setting Range (default) :

0 = On/Off, 1.0 K

1 = On/Off, 0.3 K

2 = TPI fast

3 = TPI medium

4 = TPI slow (default)


Parameter No : P89

Description : Forward shift on maximum

Setting Range (default) :

0, 0.5,…24 h

Default: 0 h


Parameter No : P90

Description : Early shutdown maximum

Setting Range (default) :

0, 0.5,…6 h

Default: 0 h


If you need more information about this Siemens RDE Room Thermostat please visit our YouTube Channel.




Comments

Post a Comment

Popular posts from this blog

Danfoss VLT micro drive FC 51 Name Plate

Image
In this Article, we are going to discuss about what specifications are mentioned on the Danfoss VLT micro drive FC 51 name plate sticker. Welcome to controls and systems blog page, The nameplate sticker is located on the top of each VFD drives and shows the ratings, serial number, warnings catalog number, and other relevant data for each unit. This nameplate sticker is mostly the same in the VLT model VFD drives, with only a few changes in the some VLT model VFD drives. 1 st ROW: ( TYPE CODE ) Position 1 - 3 [FC]-  is Product group, Possible choice is: Frequency converters, Position 4 - 6 [051]  is Series and product type, Possible choice is: Micro Drive, Position 7 - 10  [P]  is Power size, Possible choice is: 0.18 to 22 kilo watt. Position 11 - 12  [S2]  is Mains voltage, Possible choice is: S2 that means Single phase 200 to 240 Volt AC, T2 that means 3-phase, 200 to 240 Volt AC, T4 that means 3-phase, 380 to 480 Volt AC, ...
Read More »

QElectro Tech Software Overview

Image
  In This Article we are going to see QElectro Tech Software Overview... QElectro Tech QElectroTech QElectroTech is a free software to create electric diagrams. QElectroTech or QET in short is currently available in version 0.80. This Software is Very Effective and Very Useful for Electronic, Electrical, and Instrumentation Department Engineers. Compare to other Diagram Software’s ‘exe’ Setup file of QElectro Tech Software Size is Too Low. There are Lot of Electrical, Electronic and Instrumentation Symbols and elements are in this QElectro Tech software. The Software of Table of Contents is following of ( Basics , Interface , Preferences , Project , Folio , Element , Conductor , Schema , Drawing , Reports , Export and print , Annex etc..) QElectro Tech Documentation 1 QElectro Tech Documentation 2 The QElectro Tech Software contains many collections (Electrical , Logic , Hydraulic , Pneumatic and Energy symbols and Elements) also user can create they own symbols. Anyone can Acc...
Read More »

SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST

Image
   SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST This Parameter Setting is Suitable for (  Manual ON/OFF Mode , Auto Frequency Mode , Pot meter Varying Mode ) its Deepened on (0-10)v Dc signal. SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST   Parameter Setting Description P0003 1 Standard: Allows access into most frequently used parameters P0010 30 Factory setting P0970 1 Resets all parameters P0010 1 Quick commissioning P0100 0 Europe [kW], motor base frequency is 50 Hz P0301 22 Rated motor KW [KW] P0304 415 Rated motor voltage [V] P0305 35 Rated motor current [A] P0307 22 Rated motor power P0308 0.82 Rated motor cosĪ† ...
Read More »

SIEMENS V20 VFD DRIVE FAULTS CODE LIST PART-1

Image
In this article  we are going to discuss about siemens v20 vfd drive fault Cause and Remedy for this  fault codes ( F1, F2 , F3 , F4 , F5 , F6 , F11 , F12 , F20 , F35 )   SIEMENS V20 DRIVE F1  -  FAULT:    Overcurrent CAUSE : Motor power (P0307) does not correspond to the inverter power (r0206). Motor lead short circuit Earth faults r0949 = 0: Hardware reported r0949 = 1: Software reported r0949 = 22: Hardware reported REMEDY : Check the following: Motor power (P0307) must correspond to inverter power (r0206). Cable length limits must not be exceeded. Motor cable and motor must have no short-circuits or earth faults. Motor parameters must match the motor in use. Value of stator resistance (P0350) must be  correct. Motor must not be obstructed or overloaded. Increase ramp-up time (P1120) Reduce starting boost level (P1312) F2  -  FAULT:  Overvoltage CAUSE : Main supply voltage too high Motor is in regenerative mode r0949 = 0: Hardw...
Read More »

SIEMENS VFD FAULTS CODE LIST PART-2

Image
In this article  we are going to discuss about siemens v20 vfd drive fault Cause and Remedy for this fault codes ( F41, F51 , F52 , F60 , F61 , F62 , F63 , F64 , F71 , F72 ) Fault Vfd Drive F41   -  FAULT: Motor data identification  failure Motor CAUSE : Motor data identification failed. r0949 = 0: No load applied r0949 = 1: Current limit level reached during identification. r0949 = 2: Identified stator resistance less than 0.1% or greater than 100%. r0949 = 30: Current controller at voltage limit r0949 = 40: Inconsistency of identified dataset, at least one identification failed Percentage values based on the impedance Zb = Vmot,nom / sqrt(3) /  Imot,nom REMEDY : Check the following: r0949 = 0: is the motor connected to the inverter? r0949 = 1 - 49: are the motor data in P0304 - P0311 correct? Check what type of motor wiring is required (star, delta). F51 -  FAULT:   Parameter EEPROM fault EEPROM CAUSE : Read or write failure while acce...
Read More »