Siemens RDS110 Thermostat Parameter List Part-2

In This Article we are going to see SIEMENS RDS 110 THERMOSTAT Parameter List Part-2  (Humidification Setpoint , Dehumidification Setpoint , Function , Temperature Offset )

thermostat


Humidification Setpoint

Dehumidifiation
Humidification

 NO : 16

Application Settings : Comfort Humidity Setpoint

Descriptions : The Humidification setpoint for Comfort. This setpoint must be higher than the humidification setpoint for protection

Factory Settings : 40 % RH

Range :  0 to 100 % RH 

Dependencies : Display only if you've configured the output as Humidifier (no fan)


NO : 17

Application Settings : Economy Humidity Setpoint

Descriptions : The Humidification setpoint for Economy. This setpoint must be higher than the humidification setpoint for protection

Factory Settings : 40 % RH

Range :  0 to 100 % RH 

Dependencies : Display only if you've configured the output as Humidifier (no fan)


NO : 18

Application Settings : Unoccupied Humidity Setpoint

Descriptions : The Humidification setpoint for Unoccupied. This setpoint must be higher than the humidification setpoint for protection

Factory Settings : 30 % RH

Range :  0 to 100 % RH 

Dependencies : Display only if you've configured the output as Humidifier (no fan)


NO : 19

Application Settings : Protection Humidity Setpoint

Descriptions : The Humidification setpoint is maintain when you switch the thermostat to OFF under operation mode. This setpoint must be lower than the dehumidification setpoint for protection.

Factory Settings : 30 % RH

Range :  0 to 100 % RH 

Dependencies : Display only if you've configured the output as Humidifier (no fan). This setpoint is valid only if you keep default Protection option for Application setting No 37.


Note :

Humidification control works with PID algorithm. 

The algorithm continuously monitors the difference between the humidity setpoint for humidification and the measures relative air humidity in the room and switches the humidifier ON and OFF to Keep the humidity above the setpoint. 

The humidifier cannot manually be switched on and off. Changes to the setpoint impact humidification control, thereby verifying functionality.



Dehumidification Setpoint

Humidification
Dehumidification


 NO : 20

Application Settings : Comfort Dehumidity Setpoint

Descriptions : The Dehumidification setpoint for Comfort. This setpoint must be lower than the Dehumidification setpoint for protection

Factory Settings : 60 % RH

Range :  0 to 100 % RH 

Dependencies : Display only if you've configured the output as Dehumidifier (no fan)


NO : 21

Application Settings : Economy Dehumidity Setpoint

Descriptions : The Dehumidification setpoint for Economy. This setpoint must be lower than the Dehumidification setpoint for protection.

Factory Settings : 60 % RH

Range :  0 to 100 % RH 

Dependencies : Display only if you've configured the output as Humidifier (no fan)


NO : 22

Application Settings : Unoccupied Dehumidity Setpoint

Descriptions : The Dehumidification setpoint for Unoccupied. This setpoint must be lower than the humidification setpoint for protection

Factory Settings : 70 % RH

Range :  0 to 100 % RH 

Dependencies : Display only if you've configured the output as Humidifier (no fan)


NO : 23

Application Settings : Protection Dehumidity Setpoint

Descriptions : The Dehumidification setpoint to maintain when you switch the thermostat to OFF under operation mode. This setpoint must be lower than the dehumidification setpoint for protection.

Factory Settings : 70 % RH

Range :  0 to 100 % RH 

Dependencies : This setting Display only if you've configured the output as Dehumidifier (no fan). This setpoint is valid only if you keep default Protection option for Application setting No 37.


Note :

Dehumidification control works with PID algorithm. 

The algorithm continuously monitors the difference between the humidity setpoint for Dehumidification and the measures relative air humidity in the room and switches the Dehumidifier ON and OFF to Keep the humidity below the setpoint. 

The Dehumidifier cannot manually be switched on and off. Changes to the setpoint impact Dehumidification control, thereby verifying functionality.



Functions

siemens thermostat
Function


NO : 24

Application Settings : Pump / valve kick cycle

Descriptions : A Circle kicked in to turn on a constantly idle pump or valve for a minimum period of time to protect the pump or valve from being locked up. You can set the Kick-in time interval by yourself ; however, the minimum time period the pump or valve is switched ON depends on what heating controllers setting you've selected.

Factory Settings : 500 h

Range :  1 to 8760 h

Dependencies : Application setting No. 38; This function display only if you select the equipment type as one of the following in changing system setup[36], Radiator with pump, Floor heating with valve or Floor heating with pump.


NO : 25

Application Settings : Room presence detector

Descriptions : Allows switching to Comfort automatically if an unoccupied room is detected to be occupied when a scheduled Unoccupied mode is running. 

Factory Settings : Active

Range :  N/A

Dependencies : N/A



Temperature offsets

humidification


NO : 26

Application Settings : Built-in Temp Sensor adj

Descriptions : Temperature offset value for the built-in room Temperature sensor.

Factory Settings : 0 K

Range :  -5 to 5 K

Dependencies : Valid only if the built-in Temperature sensor is used to measure the Temperature.


NO : 27

Application Settings : X1 Temp sensor Adj.

Descriptions : Temperature offset value for the Room temperature sensor connected in terminal X1. 

Factory Settings : 0 K

Range :  -5 to 5 K

Dependencies : Valid only if an external room temperature sensor is connected using X1.


NO : 28

Application Settings : X2 Temp sensor Adj.

Descriptions : Temperature offset value for the Room temperature sensor connected in terminal X2. 

Factory Settings : 0 K

Range :  -5 to 5 K

Dependencies : Valid only if an external room temperature sensor is connected using X2.





Comments

Post a Comment

Popular posts from this blog

QElectro Tech Software Overview

Image
  In This Article we are going to see QElectro Tech Software Overview... QElectro Tech QElectroTech QElectroTech is a free software to create electric diagrams. QElectroTech or QET in short is currently available in version 0.80. This Software is Very Effective and Very Useful for Electronic, Electrical, and Instrumentation Department Engineers. Compare to other Diagram Software’s ‘exe’ Setup file of QElectro Tech Software Size is Too Low. There are Lot of Electrical, Electronic and Instrumentation Symbols and elements are in this QElectro Tech software. The Software of Table of Contents is following of ( Basics , Interface , Preferences , Project , Folio , Element , Conductor , Schema , Drawing , Reports , Export and print , Annex etc..) QElectro Tech Documentation 1 QElectro Tech Documentation 2 The QElectro Tech Software contains many collections (Electrical , Logic , Hydraulic , Pneumatic and Energy symbols and Elements) also user can create they own symbols. Anyone can Access
Read More »

Danfoss VLT micro drive FC 51 Name Plate

Image
In this Article, we are going to discuss about what specifications are mentioned on the Danfoss VLT micro drive FC 51 name plate sticker. Welcome to controls and systems blog page, The nameplate sticker is located on the top of each VFD drives and shows the ratings, serial number, warnings catalog number, and other relevant data for each unit. This nameplate sticker is mostly the same in the VLT model VFD drives, with only a few changes in the some VLT model VFD drives. 1 st ROW: ( TYPE CODE ) Position 1 - 3 [FC]-  is Product group, Possible choice is: Frequency converters, Position 4 - 6 [051]  is Series and product type, Possible choice is: Micro Drive, Position 7 - 10  [P]  is Power size, Possible choice is: 0.18 to 22 kilo watt. Position 11 - 12  [S2]  is Mains voltage, Possible choice is: S2 that means Single phase 200 to 240 Volt AC, T2 that means 3-phase, 200 to 240 Volt AC, T4 that means 3-phase, 380 to 480 Volt AC, Position 13 - 15  [E20]  i
Read More »

SIEMENS V20 VFD DRIVE FAULTS CODE LIST PART-1

Image
In this article  we are going to discuss about siemens v20 vfd drive fault Cause and Remedy for this  fault codes ( F1, F2 , F3 , F4 , F5 , F6 , F11 , F12 , F20 , F35 )   SIEMENS V20 DRIVE F1  -  FAULT:    Overcurrent CAUSE : Motor power (P0307) does not correspond to the inverter power (r0206). Motor lead short circuit Earth faults r0949 = 0: Hardware reported r0949 = 1: Software reported r0949 = 22: Hardware reported REMEDY : Check the following: Motor power (P0307) must correspond to inverter power (r0206). Cable length limits must not be exceeded. Motor cable and motor must have no short-circuits or earth faults. Motor parameters must match the motor in use. Value of stator resistance (P0350) must be  correct. Motor must not be obstructed or overloaded. Increase ramp-up time (P1120) Reduce starting boost level (P1312) F2  -  FAULT:  Overvoltage CAUSE : Main supply voltage too high Motor is in regenerative mode r0949 = 0: Hardware reported r0949 = 1 or 2: Software reported REMEDY
Read More »

SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST

Image
   SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST This Parameter Setting is Suitable for (  Manual ON/OFF Mode , Auto Frequency Mode , Pot meter Varying Mode ) its Deepened on (0-10)v Dc signal. SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST   Parameter Setting Description P0003 1 Standard: Allows access into most frequently used parameters P0010 30 Factory setting P0970 1 Resets all parameters P0010 1 Quick commissioning P0100 0 Europe [kW], motor base frequency is 50 Hz P0301 22 Rated motor KW [KW] P0304 415 Rated motor voltage [V] P0305 35 Rated motor current [A] P0307 22 Rated motor power P0308 0.82 Rated motor cosĪ† P0310
Read More »

Siemens RDG400KN Thermostat Parameter List

Image
In This Article we are going to see Siemens RDG400KN Room Thermostat Parameter List. RDG400KN Thermostat Control Parameter Heating only If you wish to change control parameters, proceed as follows: Press Left and Right button simultaneously for at least 3 seconds. Release them and within 2 seconds, press the Right button again for 3 seconds (The display will show P01). Select the required parameter by turning the rotary knob. Press button (OK). The current value of the selected parameter starts blinking and can be changed by turning the rotary knob. Press button (OK) to confirm the adjusted value, or (Esc) to cancel the change. If you wish to adjust additional parameters, repeat step 3 through 5, or press (Esc) to leave the parameter setting mode.
Read More »