Siemens RDS110 Thermostat Parameter List Part-3

In This Article we are going to see SIEMENS RDS 110 THERMOSTAT Parameter List Part-2  (Minimum switchover time adjustment , Other settings)

Siemens Thermostat
Siemens RDS110


Minimum Switchover Time Adjustment

thermostat


NO : 29

Application Settings : Humidify (no fan) minimum ON time

Descriptions : The minimum working time of  a standalone humidifier. This minimum limitation protects the humidifier from being destroyed by frequent switchovers.

Factory Settings : 3 min

Range :  0 to 60 min 

Dependencies : You've configured the thermostat output as Humidifier (no fan ) in changing system setup.


NO : 30

Application Settings : Humidify (no fan) minimum OFF time

Descriptions : The minimum OFF time of  a standalone humidifier. This minimum limitation protects the humidifier from being destroyed by frequent switchovers.

Factory Settings : 3 min

Range :  0 to 60 min 

Dependencies : You've configured the thermostat output as Humidifier (no fan ) in changing system setup.


NO : 31

Application Settings : Dehumidify (no fan) minimum OFF time

Descriptions : The minimum working time of  a standalone Dehumidifier. This minimum limitation protects the Dehumidifier from being destroyed by frequent switchovers.

Factory Settings : 3 min

Range :  0 to 60 min 

Dependencies : You've configured the thermostat output as Dehumidifier (no fan ) in changing system setup.


NO : 32

Application Settings : Dehumidify (no fan) minimum OFF time.

Descriptions : The minimum OFF time of  a standalone Dehumidifier. This minimum limitation protects the Dehumidifier from being destroyed by frequent switchovers.

Factory Settings : 3 min

Range :  0 to 60 min 

Dependencies : You've configured the thermostat output as Dehumidifier (no fan ) in changing system setup.


NO : 33

Application Settings : DHW minimum ON time.

Descriptions : The minimum working time of the domestic hot water boiler. this minimum limitation protects the boiler from being destroyed by frequent switchovers.

Factory Settings : 3 min

Range :  0 to 60 min 

Dependencies : You've configured the thermostat output as Domestic hot water boiler (no fan ) in changing system setup.



NO : 34

Application Settings : DHW minimum OFF time.

Descriptions : The minimum OFF time of the domestic hot water boiler. this minimum limitation protects the boiler from being destroyed by frequent switchovers.

Factory Settings : 3 min

Range :  0 to 60 min 

Dependencies : You've configured the thermostat output as Domestic hot water boiler (no fan ) in changing system setup.



Other Setting's

thermostat


NO : 35

Application Settings : Heating device electrical load.

Descriptions : The electrical load of your connected heating device. it is recommended to enter the real electrical load of your heating device. Otherwise the Temperature offset algorithm at the background may not be accurate.

Factory Settings : 0 A (2 A if you've selected the equipment type as Electric floor heating, Fan with electric heating or Electric radiator. 

Range :  0 to 5 A

Dependencies : -



NO : 36

Application Settings : Q22/Q24 Electrical Load

Descriptions : The electrical load of connected outputs

Factory Settings : 2 A  

Range :  0 to 5 A

Dependencies : Display only if you've configured an output.


NO : 37

Application Settings : OFF/protection configuration 

Descriptions : Configures whether the thermostat goes to the protection mode or completely turns off in OFF mode.

Factory Settings : Protection

Range :  Off Protection

Dependencies : N/A

 

NO : 38

Application Settings : Heating control loop

Descriptions : Indicates a different time for PWM (Pluse Width Modulation) pluse periods. you can select the default setting to let the system configure the most suitable heating controller settings based on your selected equipment type.  

Factory Settings : Default

Range :  Slow medium default fast 2-Position self-adaptive

Dependencies : N/A


NO : 39

Application Settings : Floor Temperature limit

Descriptions : Floor Temperature limit for electric floor heating  

Factory Settings : 40 °C

Range :  -50 to 80 °C

Dependencies : Valid only if you've selected the equipment type as electric floor heating and enable the floor temperature input in changing system setup. 



NO : 40

Application Settings : Optimum start control

Descriptions : Pre-heat the room in an optimum way so that you can get the scheduled temperature setpoint at your scheduled occupied time. You can choose Warm-up speed, or choose Self-adaptive to let the thermostat learn and decide the warm-up speed.  

Factory Settings : Warm-up gradient  

Range :  Warm-up gradient Self-adaptive 

Dependencies : Visible only if you're activated the optimum start control settings in changing system setup.


NO : 41

Application Settings : Warm-up gradient

Descriptions : The warm-up speed that you set to Pre-heat the room.  

Factory Settings : 30 min/K

Range :  0 to 120 min/K

Dependencies : Valid only if you've activated the optimum start control settings in changing system setup and selected Warm-up gradient for Application setting No.40



Comments

Post a Comment

Popular posts from this blog

Danfoss VLT micro drive FC 51 Name Plate

Image
In this Article, we are going to discuss about what specifications are mentioned on the Danfoss VLT micro drive FC 51 name plate sticker. Welcome to controls and systems blog page, The nameplate sticker is located on the top of each VFD drives and shows the ratings, serial number, warnings catalog number, and other relevant data for each unit. This nameplate sticker is mostly the same in the VLT model VFD drives, with only a few changes in the some VLT model VFD drives. 1 st ROW: ( TYPE CODE ) Position 1 - 3 [FC]-  is Product group, Possible choice is: Frequency converters, Position 4 - 6 [051]  is Series and product type, Possible choice is: Micro Drive, Position 7 - 10  [P]  is Power size, Possible choice is: 0.18 to 22 kilo watt. Position 11 - 12  [S2]  is Mains voltage, Possible choice is: S2 that means Single phase 200 to 240 Volt AC, T2 that means 3-phase, 200 to 240 Volt AC, T4 that means 3-phase, 380 to 480 Volt AC, ...
Read More »

QElectro Tech Software Overview

Image
  In This Article we are going to see QElectro Tech Software Overview... QElectro Tech QElectroTech QElectroTech is a free software to create electric diagrams. QElectroTech or QET in short is currently available in version 0.80. This Software is Very Effective and Very Useful for Electronic, Electrical, and Instrumentation Department Engineers. Compare to other Diagram Software’s ‘exe’ Setup file of QElectro Tech Software Size is Too Low. There are Lot of Electrical, Electronic and Instrumentation Symbols and elements are in this QElectro Tech software. The Software of Table of Contents is following of ( Basics , Interface , Preferences , Project , Folio , Element , Conductor , Schema , Drawing , Reports , Export and print , Annex etc..) QElectro Tech Documentation 1 QElectro Tech Documentation 2 The QElectro Tech Software contains many collections (Electrical , Logic , Hydraulic , Pneumatic and Energy symbols and Elements) also user can create they own symbols. Anyone can Acc...
Read More »

SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST

Image
   SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST This Parameter Setting is Suitable for (  Manual ON/OFF Mode , Auto Frequency Mode , Pot meter Varying Mode ) its Deepened on (0-10)v Dc signal. SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST   Parameter Setting Description P0003 1 Standard: Allows access into most frequently used parameters P0010 30 Factory setting P0970 1 Resets all parameters P0010 1 Quick commissioning P0100 0 Europe [kW], motor base frequency is 50 Hz P0301 22 Rated motor KW [KW] P0304 415 Rated motor voltage [V] P0305 35 Rated motor current [A] P0307 22 Rated motor power P0308 0.82 Rated motor cosĪ† ...
Read More »

SIEMENS V20 VFD DRIVE FAULTS CODE LIST PART-1

Image
In this article  we are going to discuss about siemens v20 vfd drive fault Cause and Remedy for this  fault codes ( F1, F2 , F3 , F4 , F5 , F6 , F11 , F12 , F20 , F35 )   SIEMENS V20 DRIVE F1  -  FAULT:    Overcurrent CAUSE : Motor power (P0307) does not correspond to the inverter power (r0206). Motor lead short circuit Earth faults r0949 = 0: Hardware reported r0949 = 1: Software reported r0949 = 22: Hardware reported REMEDY : Check the following: Motor power (P0307) must correspond to inverter power (r0206). Cable length limits must not be exceeded. Motor cable and motor must have no short-circuits or earth faults. Motor parameters must match the motor in use. Value of stator resistance (P0350) must be  correct. Motor must not be obstructed or overloaded. Increase ramp-up time (P1120) Reduce starting boost level (P1312) F2  -  FAULT:  Overvoltage CAUSE : Main supply voltage too high Motor is in regenerative mode r0949 = 0: Hardw...
Read More »

SIEMENS VFD FAULTS CODE LIST PART-2

Image
In this article  we are going to discuss about siemens v20 vfd drive fault Cause and Remedy for this fault codes ( F41, F51 , F52 , F60 , F61 , F62 , F63 , F64 , F71 , F72 ) Fault Vfd Drive F41   -  FAULT: Motor data identification  failure Motor CAUSE : Motor data identification failed. r0949 = 0: No load applied r0949 = 1: Current limit level reached during identification. r0949 = 2: Identified stator resistance less than 0.1% or greater than 100%. r0949 = 30: Current controller at voltage limit r0949 = 40: Inconsistency of identified dataset, at least one identification failed Percentage values based on the impedance Zb = Vmot,nom / sqrt(3) /  Imot,nom REMEDY : Check the following: r0949 = 0: is the motor connected to the inverter? r0949 = 1 - 49: are the motor data in P0304 - P0311 correct? Check what type of motor wiring is required (star, delta). F51 -  FAULT:   Parameter EEPROM fault EEPROM CAUSE : Read or write failure while acce...
Read More »