Schneider Altivar ATV-310 VFD Drive fault code Part-1

In this Article we are going to see Schneider Altivar ATV-310 VFD Drive Fault code, Possible Causes & Remedy Part-1,


Schneider
Schneider Altivar ATV-310 VFD



Code: F001 Pre Charge.

Schneider Altivar

Possible causes: Charging relay control fault or charging resistor damaged.

Remedy:

  • Turn the drive off and then back on again,
  • Check the connections,
  • Check the stability of the main supply,
  • Contact local Schneider Electric representative.

 

Code: F002 Unknown Drive Rating.

Schneider Altivar

Possible causes: Power card and stored card versions different.

Remedy: Contact local Schneider Electric representative.

 

Code: F003 Unknown or Incompatible Power Board.

Schneider Altivar

Possible causes: The power card is incompatible with the control card.

Remedy: Contact local Schneider Electric representative.

 

Code: F004 Internal Serial Link Fault.

Schneider Altivar

Possible causes: Communication interruption between the internal cards.

Remedy: Contact local Schneider Electric representative.

 

Code: F005 Invalid industrialization zone.

Schneider Altivar

Possible causes: Internal data inconsistent.

Remedy: Contact local Schneider Electric representative,

 

Code: F006 Current Measurement Circuit.

Schneider Altivar

Possible causes: Current measurement is not correct due to hardware circuit fault.

Remedy: Contact local Schneider Electric representative.

 

Code: ---- Problem with Application Firmware.

Schneider Altivar

Possible causes: Invalid application firmware update using the Multi-Loader tool,

Remedy: Re-download application firmware,

 

Code: F007 Internal Thermal Sensor Detected Fault.

Schneider Altivar

Possible causes: 

  • The drive temperature sensor is not operating correctly,
  • The drive is in short circuit or open,

Remedy: Contact local Schneider Electric representative.

 

Code: F008 Internal CPU

Schneider Altivar

Possible causes: Internal microprocessor fault,

Remedy: 

  • Turn the drive off and then back on again,
  • Contact local Schneider Electric representative.

 

Code: F009 Over Braking

Schneider Altivar

Possible causes: Sudden braking or load inertia too high.

Remedy:

  • Increase the deceleration time.
  • Install a module unit with a braking resistor if necessary.
  • Check the main supply voltage to ensure it is under the maximum acceptable (20% over maximum main supply during run status).

 

Code: F010 Over Current,

Schneider Altivar

Possible causes:

  • Parameters in the Motor control menu 300 are not correct,
  • Inertia or load too high,
  • Mechanical locking.

Remedy:

  • Check the parameters,
  • Check the size of the motor, drive, load,
  • Check the state of the mechanism.
  • Connect line motor chokes,
  • Reduce the Switching frequency range 315,
  • Check the ground connection of drive, motor cable and motor Insolation.

 

Code: F011 Drive Overheat

Schneider Altivar

Possible causes: Drive temperature too high,

Remedy: 

  • Check the motor load, the drive ventilation and the ambient temperature. 
  • Wait for the drive to cool down before restarting.

 

Code: F012 Process Overload.

Possible causes: Process overload.

Remedy: Check that drive parameters and application processes are compatible.

 


Code: F013 Motor Overload.

Schneider Altivar

Possible causes: Triggered by excessive motor current,

Remedy: Check configuration of motor thermal protection and motor load,

 


Code: F014 Output Phase Loss.

Possible causes: Loss of one phase on drive output.

Remedy:

  • Check the connections from the drive to the motor,
  • If using a downstream contactor, make sure the connection, cable and contactor are right.

 


Code: F015 Output Phases Loss.

Schneider Altivar

Possible causes:

  • Motor not connected,
  • Motor power too low, below 6% of the rated drive current,
  • Output contactor open,
  • Transient instability in the motor current,

Remedy:

  • Check the connections from the drive to the motor,
  • Test on a low power motor or without a motor. In factory settings mode, motor phase loss detection is active Output Phase loss detection.
  • To check the drive in a test or maintenance environment, without having to use a motor with the same rating as the drive, deactivate motor phase loss detection Output Phase loss detection,
  • Check and optimize IR compensation, Rated motor voltage and then perform Auto-tuning,

 

Code: F016 Main Over-Voltage.

Schneider Altivar

Possible causes:

  • Line voltage too high: - At drive power on, supply is 10% over the maximum acceptable voltage level - At power with no run command, 20% over maximal line supply.
  • Disturbed mains supply.

Remedy: 

  • Turn Off the Drive. Check and adjust the line voltage. 
  • After line come back to nominal voltage (within tolerance) do power ON. 
  • If intermittent F016 code appear, set R1 assignment 205 to 01 and it can be connected to upstream protection to avoid overvoltage in the drive. 
  • In this case LO1 can be used for others drive status,

 

Code: F017 Input Phase Loss.

Possible causes:

  • Drive incorrectly supplied or a fuse blown,
  • Failure of one phase,
  • 3-phase ATV 310 used on a single-phase line supply,
  • Unbalanced load,
  • This protection only operates with the drive on load,

Remedy:

  • Check the power connection and the fuses,
  • Use a 3-phase line supply,
  • Disable reporting of this fault type by setting Input Phase loss detection,


Code: F018 Motor short-circuit and F019 Ground short-circuit,

Schneider Altivar

Possible causes:

  • Short-circuit or grounding at the drive output,
  • Ground fault while in run state,
  • Motor switching while in run state,
  • Significant current leakage to ground while several motors are connected in parallel,

 Remedy:

  • Verify the cables connecting the drive to the motor and the motor insulation,
  • Adjust the switching frequency,
  • Connect chokes in series with the motor,
  • Verify the adjustment of speed loop.


Note:

  • Fault detection codes which cannot be cleared automatically:
  • The cause of the detected fault must be removed before resetting by cycling power to the drive.


Video Link: Schneider ALTIVAR ATV-310 VFD Drive

       



 

Comments

Post a Comment

Popular posts from this blog

Danfoss VLT micro drive FC 51 Name Plate

Image
In this Article, we are going to discuss about what specifications are mentioned on the Danfoss VLT micro drive FC 51 name plate sticker. Welcome to controls and systems blog page, The nameplate sticker is located on the top of each VFD drives and shows the ratings, serial number, warnings catalog number, and other relevant data for each unit. This nameplate sticker is mostly the same in the VLT model VFD drives, with only a few changes in the some VLT model VFD drives. 1 st ROW: ( TYPE CODE ) Position 1 - 3 [FC]-  is Product group, Possible choice is: Frequency converters, Position 4 - 6 [051]  is Series and product type, Possible choice is: Micro Drive, Position 7 - 10  [P]  is Power size, Possible choice is: 0.18 to 22 kilo watt. Position 11 - 12  [S2]  is Mains voltage, Possible choice is: S2 that means Single phase 200 to 240 Volt AC, T2 that means 3-phase, 200 to 240 Volt AC, T4 that means 3-phase, 380 to 480 Volt AC, ...
Read More »

QElectro Tech Software Overview

Image
  In This Article we are going to see QElectro Tech Software Overview... QElectro Tech QElectroTech QElectroTech is a free software to create electric diagrams. QElectroTech or QET in short is currently available in version 0.80. This Software is Very Effective and Very Useful for Electronic, Electrical, and Instrumentation Department Engineers. Compare to other Diagram Software’s ‘exe’ Setup file of QElectro Tech Software Size is Too Low. There are Lot of Electrical, Electronic and Instrumentation Symbols and elements are in this QElectro Tech software. The Software of Table of Contents is following of ( Basics , Interface , Preferences , Project , Folio , Element , Conductor , Schema , Drawing , Reports , Export and print , Annex etc..) QElectro Tech Documentation 1 QElectro Tech Documentation 2 The QElectro Tech Software contains many collections (Electrical , Logic , Hydraulic , Pneumatic and Energy symbols and Elements) also user can create they own symbols. Anyone can Acc...
Read More »

SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST

Image
   SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST This Parameter Setting is Suitable for (  Manual ON/OFF Mode , Auto Frequency Mode , Pot meter Varying Mode ) its Deepened on (0-10)v Dc signal. SIEMENS V20 VFD DRIVE MAIN PARAMETERS LIST   Parameter Setting Description P0003 1 Standard: Allows access into most frequently used parameters P0010 30 Factory setting P0970 1 Resets all parameters P0010 1 Quick commissioning P0100 0 Europe [kW], motor base frequency is 50 Hz P0301 22 Rated motor KW [KW] P0304 415 Rated motor voltage [V] P0305 35 Rated motor current [A] P0307 22 Rated motor power P0308 0.82 Rated motor cosĪ† ...
Read More »

SIEMENS V20 VFD DRIVE FAULTS CODE LIST PART-1

Image
In this article  we are going to discuss about siemens v20 vfd drive fault Cause and Remedy for this  fault codes ( F1, F2 , F3 , F4 , F5 , F6 , F11 , F12 , F20 , F35 )   SIEMENS V20 DRIVE F1  -  FAULT:    Overcurrent CAUSE : Motor power (P0307) does not correspond to the inverter power (r0206). Motor lead short circuit Earth faults r0949 = 0: Hardware reported r0949 = 1: Software reported r0949 = 22: Hardware reported REMEDY : Check the following: Motor power (P0307) must correspond to inverter power (r0206). Cable length limits must not be exceeded. Motor cable and motor must have no short-circuits or earth faults. Motor parameters must match the motor in use. Value of stator resistance (P0350) must be  correct. Motor must not be obstructed or overloaded. Increase ramp-up time (P1120) Reduce starting boost level (P1312) F2  -  FAULT:  Overvoltage CAUSE : Main supply voltage too high Motor is in regenerative mode r0949 = 0: Hardw...
Read More »

SIEMENS VFD FAULTS CODE LIST PART-2

Image
In this article  we are going to discuss about siemens v20 vfd drive fault Cause and Remedy for this fault codes ( F41, F51 , F52 , F60 , F61 , F62 , F63 , F64 , F71 , F72 ) Fault Vfd Drive F41   -  FAULT: Motor data identification  failure Motor CAUSE : Motor data identification failed. r0949 = 0: No load applied r0949 = 1: Current limit level reached during identification. r0949 = 2: Identified stator resistance less than 0.1% or greater than 100%. r0949 = 30: Current controller at voltage limit r0949 = 40: Inconsistency of identified dataset, at least one identification failed Percentage values based on the impedance Zb = Vmot,nom / sqrt(3) /  Imot,nom REMEDY : Check the following: r0949 = 0: is the motor connected to the inverter? r0949 = 1 - 49: are the motor data in P0304 - P0311 correct? Check what type of motor wiring is required (star, delta). F51 -  FAULT:   Parameter EEPROM fault EEPROM CAUSE : Read or write failure while acce...
Read More »